Finish data sheets (GME)


 

The Finish geometry data sheets

The series focuses on Glass and PET Finish Geometry (GME), providing information about the upper part of bottles or jars known as the "neck." It covers specifications for measuring neck finishes, including drawings, definitions, and dimensions for plastic and glass bottles. Various neck finish types, such as PCO, ROPP, MCA, and FEA, are available for download. The importance of these specifications is highlighted for designing molds, ensuring closure functions, compatibility with bottling lines, and serving as a basis for new designs. Special considerations include compatibility with the bottled product, filling conditions, heat treatments, storage, and distribution conditions. The data sheets emphasise collaboration with bottle manufacturers to minimize manufacturing defects.

GME12.01 - Glass finishes for snap-on pourer closures (so-called Verplast finishes)

This data sheet specifies the dimensions of the glass finish for pouring clip-on cap finish (so-called Verplast » of diameter 29 and 32 for still liquids, e.g.; oils, cordials, sauces, vinegar, …).
The following finishes are detailed in this data sheet:
  • "Verplast" diameter 29/21 for spout with a short skirt
  • "Verplast" diameter 29/21 K32 for spout with long skirt
  • "Verplast" diameter 32/24 for spout with a short skirt
for plastic caps.
12/05/2021 - Latest update 10/11/2023
GME12.10 - Finish for swing stopper

This data sheet applies to punched neck finishes which have been developed preferably for packaging made of glass and which are provided with a swing stopper per DIN 5097 - AUXILIARY MEANS OF PACKAGING - CLIPCLOCKS FOR BOTTLES
12/05/2021 - Latest update
GME13.01 - 26H180 Crown finish

Specifications and dimensions of the 26 mm tall crown finish for glass bottles containing beverages.
- Latest update 01/06/2007
GME13.02 - 26H126 Crown finish

Specifications and dimensions of the 26 mm shallow crown finish for glass bottles containing beverages.
01/06/2007 - Latest update 01/06/2007
GME13.04 - 29mm sparkling wine finish

This data sheet gives dimensions and specifications of the 29 mm glass finish for bottles intended for sparkling wine produced by a closed tank method.
This finish is designed to take a natural cork or synthetic cork stopper.
01/10/1998 - Latest update 19/01/2024
GME13.05 - 29mm Spumante crown finish

This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for Spumante-type sparkling wines.
This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.
01/10/1998 - Latest update 19/01/2024
GME13.06 - 29mm cider crown finish

This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for cider.
This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.
01/10/1998 - Latest update 19/01/2024
GME13.07 - Comparison of glass finishes for sparkling wines and other carbonated beverages

This data sheet gives an overview of the main available glass finishes available for sparkling wines and other carbonated beverages with a stopper made of cork or synthetic material, generally maintained in place with a wire cage, with or without the possibility of alternatively receiving a crown cap, in particular when the production process involves secondary fermentation in the bottle.
It is intended as a purely informative document covering the main finishes known to Cetie with no pretention to be exhaustive.
Bottlers should verify with their bottle supplier that a particular finish is adapted to their product and closure system.
23/06/2017 - Latest update 23/01/2024
GME13.08 - Traditional method sparkling wine finishes (26, 29 and 36 mm)

This data sheet gives dimensions and specifications of the glass finishes for bottles intended for sparkling wine produced by the “Traditional method”, with a diameter of 26, 29 or 36 mm.
The finish is to receive a crown cap and a cork stopper.
The dimensions of the 26- and 29-mm finish come from the French standard NF H 35-029 - BOTTLING INDUSTRY - GLASS BOTTLES - GLASS CROWN CHAMPAGNE FINISH 26 AND 29.
12/01/2018 - Latest update 10/11/2020
GME13.10 - 26H126 and 26H180 crown finishes - Dimensions

This data sheet provides specifications and dimensions of the crown finishes for glass bottles with an alternative "P" point.
  • 26 H 126 mm shallow
  • 26 H 180 mm tall
This "P" point is smoother than in the original designs  (ISO 12821 - GLASS PACKAGING  - 26 H 180 CROWN FINISH - DIMENSIONS et  ISO 12822 - GLASS PACKAGING - 26 H 126 CROWN FINISH - DIMENSIONS), to improve safety during opening. However, the filler may need to review the crown material used, as this modification could affect the interaction between the crown cap and the finish and could affect the pressure retention.
 
  • The radius at the "P" point is 1,2 mm instead of 0,5 on the ISO documents
  • The entry bore diameter is restricted to the range of 16,5 / 18 mm; diameters until 18,5 are not allowed, for tightness reasons.
16/10/2020 - Latest update 13/06/2022
GME13.11 - 26H180 crown finish - Dimensions - Modified 'P' point

This data sheet provides specifications and dimensions of the 26 H 180 mm tall crown finish for glass bottles with a modified P point. This point is smoother than in the previous finish, in order to reduce risks of breakage. The filler must pay particular attention to the material of the crown cap and to the efficient crimping, since this smoother P point retains less the cap than the former one.
12/01/2018 - Latest update 31/01/2023
GME13.12 - 26H126 crown finish - Dimensions - Modified 'P' point

This data sheet provides specifications and dimensions of the 26H126  mm shallow crown finish for glass bottles with a modified 'P' point.
12/01/2018 - Latest update 31/01/2023
GME14.00 - 26H126 & 26H180 twist crown finishes - Dimensions

This data sheet specifies the dimensions of the twist crown finishes for glass bottles.
  • 26 H 126 mm shallow
  • 26 H 180 mm tall
The twist crown finishes are designed to use an adapted metal crown cap (see e.g. EN 17177 GLASS PACKAGING - CROWN CAP - 26 mm DIAMETER, 6 mm HEIGHT CROWN CAP)

 
01/08/2022 - Latest update 05/10/2023
GME14.01 - 26H180 twist crown finish

Specifications and dimensions of the 26 mm tall twist crown finish for glass bottles containing beverages.
01/07/2003 - Latest update 05/10/2023
GME14.02 - 26H126 twist crown finish

Specifications and dimensions of the 26 mm shallow twist crown finish for glass bottles containing beverages.
01/07/2003 - Latest update 05/10/2023
GME14.11 - 26H180 twist crown finish - Reduced bore

This data sheet provides specifications and dimensions of the 26 H 180 mm tall twist crown finish for glass bottles with a bore reduced from 19,8 mm ±0,3 mm to 19,1 mm ±0,3 mm.
This finish with reduced bore should be used with prior mutual agreement between the bottler, the bottle manufacturer and the cap supplier.
11/01/2018 - Latest update 30/11/2020
GME14.12 - 26H126 twist crown finish - Reduced bore

This data sheet provides specifications and dimensions of the 26 H 126 mm shallow twist crown finish for glass bottles with a bore reduced from 19,8 mm ±0,3 mm to 19,1 mm ±0,3 mm.
This finish with reduced bore should be used with prior mutual agreement between the bottler, the bottle manufacturer and the cap supplier.
 
12/01/2018 - Latest update 30/11/2020
GME20.00 - Vacuum lug finish ø 33 medium

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 33 mm medium for wide-mouth glass containers.
 
01/01/1995 - Latest update 01/01/1995
GME20.00.10 - Vacuum lug finish ø 27 regular

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 27 mm medium for wide-mouth glass containers.
01/07/2003 - Latest update 01/07/2003
GME20.00.20 - Vacuum lug finish ø 30 and ø 33 medium

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 30  et 33 mm medium for wide-mouth glass containers.
01/07/2003 - Latest update 01/07/2003
GME20.01 - Vacuum lug finish Ø 27 and Ø 38 regular

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.02 - Vacuum lug finish Ø 38 medium

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.02.10 - Vacuum lug finish ø 38 medium

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.
01/07/2003 - Latest update 01/07/2003
GME20.03 - Vacuum lug finish Ø 43 and Ø 48 regular

This data sheet specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.04 - Vacuum lug finish ø 53 and ø 58 regular

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 53 mm and 58 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.05 - Vacuum lug finish Ø 58 deep

This document specifies the dimensions of a vacuum lug finish with a nominal size of 58 mm deep for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.06 - Vacuum lug finish ø 63, ø 66 ø 70 regular

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 29/08/2013
GME20.07 - Vacuum lug finish ø 63, ø 66 ø 70 deep

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.
01/01/1995 - Latest update 29/08/2013
GME20.08 - Vacuum lug finish Ø 77 regular

This document specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.09 - Vacuum lug finish Ø 82 regular

This document specifies the dimensions of a vacuum lug finish with a nominal size of 82 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.10 - Vacuum lug finish Ø 89 regular

This document specifies the dimensions of a vacuum lug finish with a nominal size of 89 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.11 - Vacuum lug finish Ø 100 regular

This document specifies the dimensions of a vacuum lug finish with a nominal size of 100 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME20.12 - Vacuum lug finish Ø 110 regular

This document specifies the dimensions of a vacuum lug finish with a nominal size of 110 mm regular for wide-mouth glass containers.
01/01/1995 - Latest update 01/01/1995
GME21.00 - Glass neck finish - Continuous thread - ø 43 to 90 mm

This range of neck finishes with sizes from 43 to 90 mm have one continuous thread and are designed to fit with plastic (mainly) caps.
These relatively high finishes are particularly well adapted to dry coffee content.
 
29/07/2020 - Latest update 17/12/2020
GME21.10 - Flavlock finishes ø 26 to 38 mm

This range of Flavlock neck finishes with sizes from 26 to 38 are intended as RO (Roll-On) finishes with metallic caps. The D-shaped thread run-off into the transfer bead. The deep start of the thread (S) ensures a good 'top and side' sealing. Caps have a generous level of sealing compound across the entire cap and down the sides too. These finishes are used for sauces that require to be pasteurised.
 
07/05/2021 - Latest update 29/09/2021
GME25.01 - Press-on vacuum seal finish ø 51 ø 63 ø 70

This is a vacuum top and side seal finish. 
28/08/2013 - Latest update 28/08/2013
GME28.01 - Press-on vacuum seal finish ø 51 tamper evident

This is a vacuum top and side seal finish. 
01/12/2013 - Latest update 13/01/2023
GME30.06 - BVP screw finishes for non carbonated products

Specifications and dimensions of a series of screw finishes for the closure of beverages and other non-carbonated products. Finishes designed to take a tamper-evident closure which needs to be snapped before it can be opened, commonly known as a rolled on Pilferproof closure. 
The finishes, which include all the options in figures 1 and 3, are capped with closures which may or may not have an extended skirt to cover part of the neck of the bottle. 
These finishes, with the appropriate bore control, may also be fitted with an in-bore insert to control the pour or refilling.
01/10/2001 - Latest update 01/05/2004
GME30.07 - 30 extra deep BVP finish for non-refillable insert

Specifications and dimensions of the 30 extra deep finish concerning bore diameter and profile.
The finish is designed to take a non-refillable insert for ≤ or 150 cl bottles.
01/03/2005 - Latest update 01/03/2005
GME30.08 - 31.5 deep BVP finish for non-refillable insert

Spécifications and dimensions of the 31.5 deep BVP finish concerning bore diameter and profile.
01/10/2001 - Latest update 01/04/2005
GME30.09 - 31.5 standard BVP finish for pourer

Specifications and dimensions of the 31.5 standard BVP finish concerning bore diameter and profile.
01/10/2001 - Latest update 01/10/2001
GME30.10 - Bore specifications for inserts for 30, 31,5 and 35 size BVP finishes

This data sheet gives the specifications for bore dimensions and profile for BVP finishes according to EN 15543 - GLASS PACKAGING. FINISHES FOR BOTTLES. SCREW THREAD FINISHES FOR BOTTLES FOR NON-CARBONATED LIQUIDS for 30, 31,5 and 35, standard, deep and extra deep versions, to accept pourers or non-refillable inserts, for bottles with a capacity ≤ 150 cl. As with all BVP-type finishes, these are not intended for use with carbonated products.

 
01/06/2010 - Latest update 19/01/2024
GME30.11 - Finish ALSECO-ALCOA 28mm

This data sheet specifies the dimensions of the 28-millimetre ALSECO-ALCOA screw finish for glass containers.
This finish is very close to the MCA series (See GME 32.00 - MCA FINISHES).
01/01/2000 - Latest update 13/07/2022
GME30.12 - Finish GL

This document specifies the dimensions of GL glass container knuckle thread finishes.
It applies to finishes with external screw thread, which have been developed preferably for glass packaging and are used primarily for medical or cosmetic products.
01/07/2002 - Latest update 01/07/2002
GME30.13 - Deep BVS finishes for still wines

Specifications and dimensions of a series of deep screw glass finishes for the closure of wines with a CO2 content below 1.2 g/l.
Note: Carbonation ≥ 1,2g/l in CO2 requires an appropriate bottle and an adapted capping method agreed between the glass maker, the cap supplier and the filler.
01/12/2008 - Latest update 01/12/2008
GME30.14 - 2-Start thread pilferproof finishes

This document specifies the dimensions of Pilferproof finishes equipped with a two-start thread, particularly dedicated to sweet liquids (liquors, etc…). The 3 sizes (28H44, 30H60, 31,5H60) are compatible with caps made for standard BVP finishes according to EN 15543 - GLASS PACKAGING. FINISHES FOR BOTTLES. SCREW THREAD FINISHES FOR BOTTLES FOR NON-CARBONATED LIQUIDS.


 
17/12/2020 - Latest update 17/12/2020
GME30.15 - BVP and BVS minimum through bore

This data sheet specifies the values of the minimum through bore for BVP and BVS finishes. Users of bottles need to know the minimum through bore diameter to choose the filling tube; it was therefore useful to harmonise this dimension for each finish size.


 
21/01/2022 - Latest update 07/06/2022
GME30.21 - PET finish 30/25H (18.5)

Specifications and dimensions of the 30 mm tall screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (18.5) is the height in millimetres from the top of finish to the bottom of the support ledge. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell. 
01/12/2007 - Latest update 01/12/2007
GME30.22 - PET finish 30/25-16.8-3/9

Specifications and dimensions of the 30 mm low neck screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (16.8) is the height in millimetres from the top of finish to the bottom of the support ledge. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell. 
01/12/2007 - Latest update 01/12/2007
GME30.23 - PET finish 26.7/21.8-17-3/6.35

Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 17.07 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell.
01/12/2008 - Latest update 01/12/2008
GME30.24 - PET finish 26.7/21.7-16.8-3/3

Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 16.80 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell. 
01/12/2008 - Latest update 01/12/2008
GME30.25 - PET finish 38/33-16,5-3/3

This document provides specifications and dimensions of the 38 mm screw finish with three (3) thread starts and a 16,50 mm height for still waters and non-carbonated beverages.
This finish can be used for aseptic filling and filling with introduction of nitrogen (1 bar max).
This finish is designed for non-returnable bottles and to take a tamper-evident plastic closure only.
01/03/2009 - Latest update 01/07/2024
GME30.26 - PET finish 29/25-12,6-3/2,17

Specifications and dimensions of the 29 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (12.6) is the height in millimetres from the top of finish to the bottom of the support ledge. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell.
01/06/2009 - Latest update 01/06/2009
GME30.27 - PET finish 28.3/22.5-59.5-1/3.6

Specifications and dimensions of the screw PET finish BVS 30H60 for the closure of wines with CO2 content below 1.2 grams per litre. 
This finish is designed to take :
  • An aluminium tamper-evident closure with an extended skirt which is reformed during application;
  • A screw plastic closure.
01/09/2009 - Latest update 01/09/2009
GME30.28 - PET finish 26/22-12-3/6.5

Specifications and dimensions of the 26 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for water with or without the introduction of nitrogen (internal Overpressure should not exceed 1 bar). The dimension (12.0) is the height in millimetres from the top of the finish to the bottom of the support ledge.
This finish is designed to take a tamper-evident plastic closure only. During first opening, the tamper-evident band will generally separate from the closure shell.
01/09/2011 - Latest update 01/04/2016
GME30.29 - PET finish 37/32-17,5-2/3,63

Specifications and dimensions of the 38 mm screw finish with two (2) thread starts and a 17.55 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal overpressure should not exceed 1 bar). This finish is designed to take a tamper-evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell.
This finish is for non-crystallized necks only.
13/05/2013 - Latest update 01/07/2024
GME30.30 - PET finish 33/28-12.9-2/5

This data sheet provides specifications and dimensions of the 33 mm screw finish with two (2) thread starts for flat waters and non-carbonated beverages.
This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar).
This finish is designed to take a tamper evident plastic closure only.
During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell.
01/08/2011 - Latest update
GME30.31 - PET finish 32/26-15,8-2/2,7-(HF)

This document provides specifications and dimensions of the 32 mm amorphous screw finish with two (2) thread starts for still waters and non-carbonated beverages (the internal pressure should not exceed 1 bar). This finish can be used for hot filling (HF) with a maximum temperature up to 88°C. It is designed to take a tamper evident plastic closure only.
This finish should be compatible with the use of attached closures as required in the EU Directive 2019/904, even if it has not been industrially validated at the date of publication
 
01/01/2016 - Latest update 15/03/2023
GME30.32 - PET finish 26/21-8.5 for edible oil

This document provides specifications and dimensions of the 26 mm finish designed for a snap-on plastic closure for non-carbonated products like edible oils, vinegar and sauces, cold filled (e.g. ambient temperature) with or without introduction of nitrogen (the internal pressure should not exceed 1 bar).
This finish is designed to take a tamper-evident plastic closure only.
28/04/2014 - Latest update 23/12/2022
GME30.33 - PET finish 29/21-10.5 for edible oil

This document provides specifications and dimensions of the 29 mm snap-on finish for non-carbonated products like alimentary oils, vinegar and sauces, cold filled (ambient temperature) with or without introduction of nitrogen (the internal pressure should not exceed 1 bar). This finish is designed to take plastic closure with or without a tamper-evident feature.
28/04/2014 - Latest update 01/07/2021
GME30.34 - BVS PCO PET finish 21,4/16,7-29-1/2,5

This data sheet provides specifications and dimensions of the BVS PCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar.
This finish is designed to take a plastic tamper evident closure, which is applied by screwing.
01/11/2014 - Latest update 17/01/2018
GME30.35 - BVP MCO PET bague 21,4/16-29-1/2,5

This data sheet provides specifications and dimensions of the BVP MCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar.
This finish is designed to take an aluminium tamper-evident closure, which is crimped during application.
20/09/2013 - Latest update 17/01/2018
GME30.36 - PET finish 32/27-14.9-2/2,7

This document provides specifications and dimensions of the 32 mm screw finish with two (2) thread starts for still waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar). This finish is designed to take a tamper evident plastic closure only.
 
14/11/2013 - Latest update 20/11/2023
GME30.37 - PET finish 26/22-12,9-1/2,17 version 4,2 % vol CO2

This data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages up to 8,4g CO2/l (4,2 vol % CO2) content and bottles of up to and including 2,0 l litres in capacity.
Important note: This replaces previous editions foreseen up to 7g CO2/l (3,5 vol % CO2) and includes an extra thread segment. The previous version is not suitable for carbonation levels over 7g CO2/l (3,5 vol % CO2).
This finish is intended for non-refillable bottles, has vent slots and is designed to take a tamper evident plastic closure engaging on a bead foreseen for this purpose.
01/04/2016 - Latest update 01/10/2020
GME30.38 - PET finish 26/22-12-1/2,5

Specifications and dimensions of the 26 mm screw finish with one (1) thread start for carbonated beverages up to 7g/l CO2 content and for bottles up to 1,5 litres. The dimension (12,0) is the height in millimetres from the top of the finish to the bottom of the support ledge, offering line interchangeability with the current three (3) thread starts neck finish for flat water (GME30.28 - PET FINISH 26/22-12-3/6.5). This finish has vent slots and is designed to take a tamper-evident plastic closure.
01/07/2015 - Latest update 25/11/2020
GME30.39 - PET finish 25/22-9,5-3/1,73

Specifications and dimensions of the 25 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages in small package sizes with up to 1.5 l volume. This finish can be used for aseptic filling and filling with introduction of nitrogen (internal overpressure should not exceed 1 bar). This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck.
01/07/2017 - Latest update 17/04/2020
GME30.40 - PET finish 26/22-15,1-1/2,3

This data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages,
  • Up to 10,2g CO2/l (5,2 vol CO2) content for bottles of up to and including 2,0 litres in capacity, and
  • up to 8,8g CO2/l (4,5 vol CO2) content and bottles of up to and including 3,0 litres in capacity.
This finish is intended for non-refillable bottles, has vent slots and is designed to take a tamper-evident plastic closure engaging on a bead foreseen for this purpose.
The requirements of the EU directive 2019/904 were taken into account during the development of this neck finish.
22/12/2022 - Latest update 22/12/2022
GME30.41 - PET finish 26/22-13,4-1/2,3

This experimental data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages,
  • Up to 10,2g CO2/l (5,2 vol CO2) content for bottles of up to and including 2,0 litres in capacity, and
  • up to 8,8g CO2/l (4,5 vol CO2) content and bottles of up to and including 3,0 litres in capacity.
This finish is intended for non-refillable bottles, has vent slots and is designed to take a tamper-evident plastic closure engaging on a bead foreseen for this purpose.
This finish is not intended for the use of attached closures; The GME30.40 - PET FINISH 26/22-15,1-1/2,3 presents a related neck finish designed for attached closures.
 
10/07/2020 - Latest update 22/12/2022
GME30.43 - PET finish 47/41-19,5-3/3,40

This document provides specifications and dimensions of the 47 mm screw finish with three (3) thread starts for non-carbonated pressurised and non-pressurised beverages. This finish can be used for filling with introduction of nitrogen (internal overpressure should not exceed 1 bar). The dimension (19,5) is the height in millimetres from the top of finish to the bottom of the support ledge. This finish is designed to take a tamper-evident plastic closure only. During first opening, the tamper- evident band will separate from the closure shell and stay on a one-way bottle neck or as it is the case for bottles on the returnable market, the tamper-evident band will tear but will remain connected to the closure shell.
10/03/2021 - Latest update 10/03/2021
GME30.44 - Lightweight PET finish 29/25-12,6-3/2,17

This document provides specifications and dimensions of the 29 mm lightweight screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for filling with the introduction of nitrogen (internal overpressure should not exceed 1 bar). The dimension (12.6) is the height in millimeters from the top of the finish to the bottom of the support ledge. This finish is designed to take a tamper-evident plastic closure only. During the first opening, the temper-evident band will separate from the closure shell and stay on a one-way bottle neck or like bottles in the returnable market, the tamper-evident band will tear but will remain connected to the closure shell.
28/07/2023 - Latest update
GME30.70 - PET snap neck finish 26/21-8,5mm

This document provides specifications and dimensions of the 26 mm finish designed for a snap-on plastic closure for non-pressurised and non-carbonated beverages cold-filled (e.g. ambient temperature) without the introduction of nitrogen. This finish is designed for snap-on plastic closure only, with or without tamper-evident features.
 
10/12/2020 - Latest update 10/12/2020
GME305 - Pilferproof finishes for non-pressurised products supplementary series

Dimensions of a series of screw finishes for the closure of beverages and other non-carbonated products. 
02/11/1977 - Latest update 03/01/1983
GME306 - 25 pilferproof finishes for Alpha syrup

Dimensions of the 25 mm pilferproof glass neck finish for Alpha syrups.
01/03/1989 - Latest update 01/03/1989
GME307 - 28 pilferproof finishes for alpha syrups

Dimensions of the 28 mm pilferproof glass neck finish for Alpha syrups.
01/03/1989 - Latest update 01/03/1989
GME32.00 - MCA finishes

This data sheet specifies the dimensions of the various 28-millimetre screw finish for glass containers designated MCA.
01/06/2008 - Latest update 21/07/2022
GME32.01 - 28mm screw finish for bottles with internal pressure

Specifications and dimensions of the 28 millimetres screw finish for one-way or returnable glass containers with internal pressure designated MCA 3 finish. This document has been superseded by standard EN 17829 - GLASS PACKAGING - 28 MILLIMETRE-SCREW FINISHES (MCA RANGE) - DIMENSIONS.
01/02/1995 - Latest update 01/02/1995
GME32.02 - 28mm screw finish 7.5 RF universal for bottles with internal pressure

Specifications and dimensions of the 28 mm finish for glass containers for pressurised or vacuum liquids. 
01/01/1983 - Latest update 01/11/1999
GME32.03 - PET PCO finish 27/22-21-1/3,18

Specifications and dimensions of the single start thread 27,43 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper-evident plastic closure only. During first opening, the tamper-evident band will separate from the closure shell and stay on a one-way bottle neck or as it is the case for bottles on the returnable market, the tamper-evident band will tear but will remain connected to the closure shell.

 
01/06/2006 - Latest update 20/09/2021
GME32.04 - PET PCO finish 28/22-17-1/2.7

Specifications and dimensions of the single start thread lightweight 28 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper-evident plastic closure only. During first opening, the tamper-evident band will separate from the closure shell and stay on a one-way bottle neck or like bottles in the returnable market, the tamper-evident band will tear but will remain connected to the closure shell.
This Cetie document is no longer available. For more information, refer to PCO - 1881 neck finish developed by ISBT (International Society of Beverage Technologists), as illustrated in drawing N° 3784253. ISBT technical drawings can be downloaded from https://www.isbt.com/threadspecs-downloads.asp.
01/03/2009 - Latest update 01/03/2009
GME32.05 - MCA 1 finish

Specifications and dimensions of the 28 millimetres screw finish for glass containers designated MCA 1 finish. 
01/06/2009 - Latest update 01/06/2009
GME32.06 - MCA 7.5 R finish

This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 7,5 R finish for returnable glass. 
01/06/2009 - Latest update 14/09/2023
GME320 - Pilferproof finish for pressured beverages

01/01/1983 - Latest update 01/01/1983
GME33.01 - PET neck finish 27/22-13,5/1/4,24-1,5 turns for HPC applications

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 27,38 mm, and denominated as 27/22-13,5/1/4,24-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also gives an explanation regarding the dimensions and neck features applied as well as dimensions for the preforms weight range from 13g up to 42g
13/05/2019 - Latest update 22/12/2022
GME33.02 - PET neck finish 37/32-13,5/1/4,24-1,5 turns for HPC applications

This document aims to fully specify a PET Neck Finish standard for HPC market with a nominal crest of thread diameter of 37 mm and denominated as 37/32-13,5/1/4,24-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also explains the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 19,5g up to 58g.
23/04/2020 - Latest update 22/12/2022
GME33.03 - PET neck finish 43/37-14,7-1/4,24-1,25 turns for HPC applications

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 43 mm and denominated as 43/37-14,7-1/4,24-1,25 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also gives an explanation regarding the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 28 g up to 83 g for the option with Ø Z = 42,80 and from 28 g up to 92 g for the option Ø Z = 47.
23/04/2020 - Latest update 22/12/2022
GME33.04 - PET neck finish 24/18-11,5-1/3,18-1,5 turns for HPC applications

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 23,67 mm and denominated as 24/18-11,5-1/3,18-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also explains the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 11,8 g up to 27,5 g.
 
29/10/2020 - Latest update 22/12/2022
GME33.05 - PET neck finish 20/15-11,5-1/3,18-1,5 turns for HPC applications

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 20mm and denominated as 20/15-11,5-1/3,18-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also gives an explanation regarding the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 9,6 g up to 15 g.
16/12/2020 - Latest update 22/12/2022
GME33.50 - PET snap neck Finish 27/22-6,3 for HPC applications

This document aims to fully specify a PET Neck Finish standard for HPC market with a nominal crest of snap diameter of 27 mm, and denominated as 27/22-6,3 (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also explains the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 28g up to 42g.
 
10/06/2020 - Latest update 15/02/2021
GME33.51 - PET snap neck finish 27/22-6,3 for HPC applications for high speed lines

This document is an adaptation of the GME33.50 - PET SNAP NECK FINISH 27/22-6,3 FOR HPC APPLICATIONS for high-speed lines. It aims to fully specify a PET Neck Finish standard for the HPC market with the nominal crest of snap diameter of 2 7 mm and denominated as 27 / 22 - 6,3. It also gives an explanation regarding the dimensions and neck features applied as well as dimensions for the exemplary preforms weight range from 28 gr up to 42 gr.
 
15/09/2021 - Latest update 15/06/2022
GME40.02 - Flaconnage - Neck finish for plug pump

Specifications and dimensions of a series of finishes for pump systems with internal fixation on glass bottles.
01/01/2005 - Latest update 13/09/2022
GME40.03 - Flaconnage - Neck finish for snap-in pump

Specifications and dimensions of a finish for pump systems with internal fixation on glass bottles.
See the example of pump references in table 1.
01/02/2006 - Latest update 25/05/2024
GME40.04 - Flaconnage - Neck finish for crimpless pump

Specifications and dimensions of a series of neck finishes for pump systems with external fixation, without crimping, on glass bottles.
This geometry is dedicated to SP7 and SP8 from Silgan. Other crimpless pumps are adapted to standard EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES FOR AEROSOL AND SPRAY GLASS CONTAINERS.
01/01/2007 - Latest update 13/09/2022
GME40.05 - Dimensions of the neck finish for glass aerosol containers

This data sheet specifies the dimensions of the neck finish of glass aerosol containers and pumps to ensure complete tightness of valves or pumps with finishes as defined in EN 14849 - AEROSOL CONTAINERS - GLASS CONTAINERS - DIMENSIONS OF AEROSOL VALVE FERRULES. It applies to moulded glass containers with neck diameters of 13mm, 15mm, 17mm, 18mm and 20mm. This data sheet is intended to serve as a basis for the revision of the existing EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES FOR AEROSOL AND SPRAY GLASS CONTAINERS standard, which will be published in late 2021. The standard replaces the GME40.05 data sheet, and therefore it is deleted from the Cetie library.
03/12/2014 - Latest update 29/04/2016
GME40.06 - Stepped FEA finish

This range of FEA glass neck finishes with sizes 18 and 20 are designated for aerosol dispensers. This document was established from the INE BV96037 data sheet. The step of 0,2 mm can be used for protecting the upper part of the plastic coating and integrating it under the crimped ferrule.
03/02/2022 - Latest update 06/12/2023
GME40.07 - Flaconnage - Glass finish for screw pump - CV finish

This data sheet is based on the INE BV95045 data sheet. It specifies the dimensions of a screw finish for glass flacons for the perfume or cosmetics industry. It applies to glass containers with a nominal diameter of the neck finish around 13, 15, 17, 18 or 20 mm. The designation is "CV 13", "CV 15", "CV 17", "CV 18" and "CV 20".
08/12/2021 - Latest update
GME40.08 - Flaconnage - Neck finish '10,6' for snap-on pump type 'Replica ST'

This document specifies the dimensions of a 10,6-mm neck finish dedicated to a snap-on (crimpless) Replica ST pump from APTAR.
ST stands for Seal-Tight.
30/01/2023 - Latest update 25/05/2024
GME40.10 - Flaconnage - Neck finish 11 mm for snap-on (Click-it) SP5-K pump

This document specifies the dimensions of an 11 mm neck finish dedicated to a snap-on (Click-it) 'SP5-K' pump from SILGAN.
13/10/2023 - Latest update 21/11/2024
GME40.20 - Flaconnage - Sustainable neck finishes - Screw neck without additional bead

This data sheet specifies dimensions of a screw neck finish without additional bead for glass bottles dedicated to perfume and cosmetics.
It applies to glass containers with a nominal diameter of the neck finish around 13, 15 or 17 mm

This neck finish is part of a range of neck finishes specifically designed to:
- Keep the components (collar, cap, ...) of an existing packaging, when switching from a crimped neck finish (EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES FOR AEROSOL AND SPRAY GLASS CONTAINERS) to a screw neck finish ;
- Refill bottles using a plastic screw ferrule instead of an aluminium one, thus avoiding possible frictions.

Screw neck finishes are based on the thread defined by GPI 415 - TALL CONTINUOUS THREAD CONCEALED BEAD FINISH (SIZES 13-28) to create the plastic screw ferrule (the ferrule is thicker in plastic than in metal).

The rice grains are intended to limit the risk of self-unscrewing (neck lubrication by the content, ...) Option to choose depending on the development.

The finish exists with and without additional bead. The version without bead is not compatible with heavy bottles, the limit weight shall be validated with the glassmaker according to the shape of the bottle.

Designation of the finish :
-    SNI 15: (Screw Neck International diameter 15)
-    CNI 15: (Crimped Neck International diameter 15)

For the screw neck finish without an additional bead, refer to the GME40.20 - FLACONNAGE - SUSTAINABLE NECK FINISHES - SCREW NECK WITHOUT ADDITIONAL BEAD.
For the screw neck finish with additional bead, refer to the GME40.25 - FLACONNAGE - SUSTAINABLE NECK FINISHES - INTERCHANGEABLE SCREW NECK WITH ADDITIONAL BEAD.
17/03/2021 - Latest update 01/07/2024
GME40.25 - Flaconnage - Sustainable neck finishes - Interchangeable screw neck with additional bead

This data sheet specifies the dimensions of an interchangeable screw neck finish with additional bead for glass bottles dedicated to perfume and cosmetics.
It applies to glass containers with a nominal diameter of the neck finish around 13, 15 or 17 mm

This neck finish is part of a range of neck finishes specifically designed to:
- Allow interchangeability of the bottle mould between crimped neck finishes and screw neck finishes (for versions with bead) ;
- Keep the components (collar, cap, ...) of an existing packaging, when switching from a crimped neck finish (EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES FOR AEROSOL AND SPRAY GLASS CONTAINERS) to a screw neck finish ;
- Refill bottles using a plastic screw ferrule instead of an aluminium one, thus avoiding possible friction.
Screw neck finishes are based on the thread defined by GPI 415 - TALL CONTINUOUS THREAD CONCEALED BEAD FINISH (SIZES 13-28) to create the plastic screw ferrule (the ferrule is thicker in plastic than in metal).

The rice grains are intended to limit the risk of self-unscrewing (neck lubrication by to the content, ...) An option to choose depending on the development.

The finish exists with and without additional bead. The version without bead is not compatible with heavy bottles, the limit weight shall be validated with the glassmaker according to the shape of the bottle.

Designation of the finish:
- SNI 15: (Screw Neck International diameter 15)
- CNI 15: (Crimped Neck International diameter 15)

For the screw neck finish without an additional bead, refer to the GME40.20 - FLACONNAGE - SUSTAINABLE NECK FINISHES - SCREW NECK WITHOUT ADDITIONAL BEAD.
For the screw neck finish with additional bead, refer to the GME40.25 - FLACONNAGE - SUSTAINABLE NECK FINISHES - INTERCHANGEABLE SCREW NECK WITH ADDITIONAL BEAD.


 
17/03/2021 - Latest update 01/07/2024
GME40.30 - Flaconnage - Sustainable neck finishes - Interchangeable crimped finish with additional bead

This data sheet specifies the dimensions of an interchangeable crimped neck finish with additional bead for glass bottles dedicated to perfume and cosmetics.
It applies to glass containers with a nominal diameter of the neck finish around 15 or 17 mm

This neck finish is part of a range of neck finishes specifically designed to:
- Allow interchangeability of the bottle mould between crimped neck finishes and screw neck finishes (for versions with bead) ;
- Keep the components (collar, cap, ...) of existing packaging, when switching from a crimped neck finish (EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES FOR AEROSOL AND SPRAY GLASS CONTAINERS) to a screw neck finish ;
- Refill bottles using a plastic screw ferrule instead of an aluminium one, thus avoiding possible friction.
Screw neck finishes are based on the thread defined by GPI 415 - TALL CONTINUOUS THREAD CONCEALED BEAD FINISH (SIZES 13-28) to create the plastic screw ferrule (the ferrule is thicker in plastic than in metal).

Designation of the finish:

- SNI 15: (Screw Neck International diameter 15)
- CNI 15: (Crimped Neck International diameter 15)

For the screw neck finish without an additional bead, refer to the GME40.20 - FLACONNAGE - SUSTAINABLE NECK FINISHES - SCREW NECK WITHOUT ADDITIONAL BEAD.
For the screw neck finish with additional bead, refer to the GME40.25 - FLACONNAGE - SUSTAINABLE NECK FINISHES - INTERCHANGEABLE SCREW NECK WITH ADDITIONAL BEAD.
 
17/03/2021 - Latest update 01/07/2024
GME401 - Glass finish at 38mm standard ROPP (7 turns per inch)

This data sheet provides specifications and dimensions for the 38 mm standard ROPP glass finish.
01/09/1987 - Latest update 01/09/1987
GME402 - Lug finish 20mm for antibiotic and freeze dry glass containers

01/06/1987 - Latest update 01/06/1987
GME50.01 - Cork mouth finish for corks and capsules

This data sheet specifies the dimensions of a cork mouth finish for corks and capsules for glass bottles, for wine that has a carbonation pressure not exceeding 2.0 g CO2/l, for use with natural corks.
01/04/1992 - Latest update 01/04/1992
GME50.02 - Glass bottle - Specifications of a neck finish with entry bore diameter 17,5mm

This document sets out the dimensional characteristics of a finish with a narrow entry bore (diameter 17,5 mm) for bottles containing a wine that has a carbonation not exceeding 1,2 g CO2/l with internal sealing.

Note: Carbonation over 1,2 g CO2/l requires a suitable container and stopper agreed between the glassmaker, the stopper manufacturer, and the packer/filler.
For dimensions and requirements not defined in this document, refer to the standard EN 12726 - PACKAGING - CORK MOUTH FINISH WITH A BORE DIAMETER OF 18,5 mm FOR CORKS AND TAMPER EVIDENT CAPSULES.
29/05/2024 - Latest update 29/05/2024
GME51.00 - Glass bottle - Bar-top stopper 27, 29, or 34 mm neck finish, stopper and overcap

This datasheet sets out the dimensional characteristics of the finish of bottles intended for the packaging of alcohols, spirits, liquors and fortified wines and musts. It takes up and completes the dimensions contained in the French standard NFH 35 081 - BOTTLING INDUSTRY - GLASS BOTTLES - 27, 29, 34 HEAD CORK STOPPER - NECK GLASS FINISH - COMPOSITE STOPPER - OVERCAPSULE and specifies the inner profile of the finish.
02/10/2019 - Latest update

Cookie Usage Notice

By continuing to browse this website, you consent to the use of Cetie's cookies. These cookies enable us to provide you with an optimal browsing experience and to measure our website's audience.

If you choose to click 'Refuse', the website will remain accessible; however, you may experience interruptions or limited functionality in certain areas.



Accept  Learn more and manage cookies  Refuse