Finish data sheets (GME) Cetie | Finish data sheets

GME12.01 - Glass finishes for snap-on pourer closures (so-called Verplast finishes)

12/05/2021 - Latest update 10/11/2023

This data sheet specifies the dimensions of the glass finish for pouring clip-on cap finish (so-called Verplast » of diameter 29 and 32 for still liquids, e.g.; oils, cordials, sauces, vinegar, …). The following finishes are detailed in this data sheet: "Verplast" ...

See detail

GME12.10 - Finish for swing stopper

12/05/2021 - Latest update 05/06/2025

This data sheet applies to punched neck finishes which have been developed preferably for packaging made of glass and which are provided with a swing stopper.

See detail

GME13.01 - 26H180 Crown finish

- Latest update 01/06/2007

Specifications and dimensions of the 26 mm tall crown finish for glass bottles containing beverages.

See detail

GME13.02 - 26H126 Crown finish

01/06/2007

Specifications and dimensions of the 26 mm shallow crown finish for glass bottles containing beverages.

See detail

GME13.04 - 29mm sparkling wine finish

01/10/1998 - Latest update 19/01/2024

This data sheet gives dimensions and specifications of the 29 mm glass finish for bottles intended for sparkling wine produced by a closed tank method. This finish is designed to take a natural cork or synthetic cork stopper.

See detail

GME13.05 - 29mm Spumante crown finish

01/10/1998 - Latest update 19/01/2024

This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for Spumante-type sparkling wines. This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.

See detail

GME13.06 - 29mm cider crown finish

01/10/1998 - Latest update 19/01/2024

This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for cider. This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.

See detail

GME13.07 - Comparison of glass finishes for sparkling wines and other carbonated beverages

23/06/2017 - Latest update 23/01/2024

This data sheet gives an overview of the main available glass finishes available for sparkling wines and other carbonated beverages with a stopper made of cork or synthetic material, generally maintained in place with a wire cage, with or without the possibility of alternatively receiving a ...

See detail

GME13.08 - Traditional method sparkling wine finishes (26, 29 and 36 mm)

12/01/2018 - Latest update 24/10/2024

This data sheet gives dimensions and specifications of the glass finishes for bottles intended for sparkling wine produced by the “Traditional method”, with a diameter of 26, 29 or 36 mm. The finish is to receive a crown cap and a cork stopper. The dimensions of the 26- and 29-mm ...

See detail

GME13.10 - 26H126 and 26H180 crown finishes - Dimensions - alternative P point

16/10/2020 - Latest update 13/06/2022

This data sheet provides specifications and dimensions of the crown finishes for glass bottles with an alternative "P" point. 26 H 126 mm shallow 26 H 180 mm tall This "P" point is smoother than in the original designs (ISO 12821 - GLASS ...

See detail

GME13.11 - 26H180 crown finish - Dimensions - alternative 'P' point

12/01/2018 - Latest update 31/01/2023

This data sheet provides specifications and dimensions of the 26 H 180 mm tall crown finish for glass bottles with a modified P point. This point is smoother than in the previous finish, in order to reduce risks of breakage. The filler must pay particular attention to the material of the crown ...

See detail

GME13.12 - 26H126 crown finish - Dimensions - alternative 'P' point

12/01/2018 - Latest update 31/01/2023

This data sheet provides specifications and dimensions of the 26H126 mm shallow crown finish for glass bottles with a modified 'P' point.

See detail

GME14.00 - 26H126 & 26H180 twist crown finishes - Dimensions

01/08/2022 - Latest update 05/10/2023

This data sheet specifies the dimensions of the twist crown finishes for glass bottles. 26 H 126 mm shallow 26 H 180 mm tall The twist crown finishes are designed to use an adapted metal crown cap (see e.g. EN 17177 - GLASS PACKAGING - CROWN CAP - 26 mm DIAMETER, 6 mm HEIGHT ...

See detail

GME14.01 - 26H180 twist crown finish

01/07/2003 - Latest update 05/10/2023

Specifications and dimensions of the 26 mm tall twist crown finish for glass bottles containing beverages.

See detail

GME14.02 - 26H126 twist crown finish

01/07/2003 - Latest update 05/10/2023

Specifications and dimensions of the 26 mm shallow twist crown finish for glass bottles containing beverages.

See detail

GME14.11 - 26H180 twist crown finish - Reduced bore

11/01/2018 - Latest update 24/01/2025

This data sheet provides specifications and dimensions of the 26 H 180 mm tall twist crown finish for glass bottles with a bore reduced from 19,8 mm ±0,3 mm to 19,1 mm ±0,3 mm. This finish with reduced bore should be used with prior mutual agreement ...

See detail

GME14.12 - 26 h 126 twist crown finish - Reduced bore

12/01/2018 - Latest update 24/01/2025

This data sheet provides specifications and dimensions of the 26 H 126 mm shallow twist crown finish for glass bottles with a bore reduced from 19,8 mm ±0,3 mm to 19,1 mm ±0,3 mm. This finish with reduced bore should be used with prior mutual ...

See detail

GME20.00 - Vacuum lug finish ø 33 medium

01/01/1995

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 33 mm medium for wide-mouth glass containers.

See detail

GME20.00.10 - Vacuum lug finish ø 27 regular

01/07/2003

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 27 mm medium for wide-mouth glass containers.

See detail

GME20.00.20 - Vacuum lug finish ø 30 and ø 33 medium

01/07/2003

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 30 et 33 mm medium for wide-mouth glass containers.

See detail

GME20.01 - Vacuum lug finish Ø 27 and Ø 38 regular

01/01/1995

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm regular for wide-mouth glass containers.

See detail

GME20.02 - Vacuum lug finish Ø 38 medium

01/01/1995

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.

See detail

GME20.02.10 - Vacuum lug finish ø 38 medium

01/07/2003

This data sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.

See detail

GME20.03 - Vacuum lug finish Ø 43 and Ø 48 regular

01/01/1995

This data sheet specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers.

See detail

GME20.04 - Vacuum lug finish ø 53 and ø 58 regular

01/01/1995

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 53 mm and 58 mm regular for wide-mouth glass containers.

See detail

GME20.05 - Vacuum lug finish Ø 58 deep

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 58 mm deep for wide-mouth glass containers.

See detail

GME20.06 - Vacuum lug finish ø 63, ø 66 ø 70 regular

01/01/1995 - Latest update 29/08/2013

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm regular for wide-mouth glass containers.

See detail

GME20.07 - Vacuum lug finish ø 63, ø 66 ø 70 deep

01/01/1995 - Latest update 29/08/2013

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.

See detail

GME20.08 - Vacuum lug finish Ø 77 regular

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for wide-mouth glass containers.

See detail

GME20.09 - Vacuum lug finish Ø 82 regular

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 82 mm regular for wide-mouth glass containers.

See detail

GME20.10 - Vacuum lug finish Ø 89 regular

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 89 mm regular for wide-mouth glass containers.

See detail

GME20.11 - Vacuum lug finish Ø 100 regular

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 100 mm regular for wide-mouth glass containers.

See detail

GME20.12 - Vacuum lug finish Ø 110 regular

01/01/1995

This document specifies the dimensions of a vacuum lug finish with a nominal size of 110 mm regular for wide-mouth glass containers.

See detail

GME21.00 - Glass neck finish - Continuous thread - ø 43 to 90 mm

29/07/2020 - Latest update 05/06/2025

This range of neck finishes with sizes from 43 to 90 mm have one continuous thread and are designed to fit with plastic (mainly) caps. These relatively high finishes are particularly well adapted to dry coffee content. This document is based on the British Glass GF316 data sheet.

See detail

GME21.10 - Flavlock finishes ø 26 to 38 mm

07/05/2021 - Latest update 29/09/2021

This range of Flavlock neck finishes with sizes from 26 to 38 are intended as RO (Roll-On) finishes with metallic caps. The D-shaped thread run-off into the transfer bead. The deep start of the thread (S) ensures a good 'top and side' sealing. Caps have a generous level of sealing ...

See detail

GME25.01 - Press-on vacuum seal finish ø 51 ø 63 ø 70

28/08/2013

This is a vacuum top and side seal finish.

See detail

GME28.01 - Press-on vacuum seal finish ø 51 tamper evident

01/12/2013 - Latest update 13/01/2023

This is a vacuum top and side seal finish.

See detail

GME30.06 - BVP screw finishes for non carbonated products

01/10/2001 - Latest update 01/05/2004

Specifications and dimensions of a series of screw finishes for the closure of beverages and other non-carbonated products. Finishes designed to take a tamper-evident closure which needs to be snapped before it can be opened, commonly known as a rolled on Pilferproof closure. The ...

See detail

GME30.07 - 30 extra deep BVP finish for non-refillable insert

01/03/2005

Specifications and dimensions of the 30 extra deep finish concerning bore diameter and profile. The finish is designed to take a non-refillable insert for ≤ or 150 cl bottles.

See detail

GME30.08 - 31.5 deep BVP finish for non-refillable insert

01/10/2001 - Latest update 01/04/2005

Spécifications and dimensions of the 31.5 deep BVP finish concerning bore diameter and profile.

See detail

GME30.09 - 31.5 standard BVP finish for pourer

01/10/2001

Specifications and dimensions of the 31.5 standard BVP finish concerning bore diameter and profile.

See detail

GME30.10 - Bore specifications for inserts for 30, 31,5 and 35 size BVP finishes

01/06/2010 - Latest update 19/01/2024

This data sheet gives the specifications for bore dimensions and profile for BVP finishes according to EN 15543 - GLASS PACKAGING. FINISHES FOR BOTTLES. SCREW THREAD FINISHES FOR BOTTLES FOR NON-CARBONATED LIQUIDS for 30, 31,5 and 35, standard, deep and extra deep versions, to accept pourers or ...

See detail

GME30.11 - Finish ALSECO-ALCOA 28mm

01/01/2000 - Latest update 13/07/2022

This data sheet specifies the dimensions of the 28-millimetre ALSECO-ALCOA screw finish for glass containers. This finish is very close to the MCA series (See GME 32.00 - MCA FINISHES).

See detail

GME30.12 - Finish GL

01/07/2002

This document specifies the dimensions of GL glass container knuckle thread finishes. It applies to finishes with external screw thread, which have been developed preferably for glass packaging and are used primarily for medical or cosmetic products.

See detail

GME30.13 - Deep BVS finishes for still wines

01/12/2008 - Latest update 28/03/2012

Specifications and dimensions of a series of deep screw glass finishes for the closure of wines with a CO2 content below 1.2 g/l. Note: Carbonation ≥ 1,2g/l in CO2 requires an appropriate bottle and an adapted capping method agreed between the glass maker, the cap supplier and the filler.

See detail

GME30.14 - 2-start thread pilfer-proof finishes

17/12/2020 - Latest update 05/06/2025

This document specifies the dimensions of pilfer-proof finishes with a two-start thread, particularly dedicated to sweet liquids (liquors, etc…). The 3 sizes (28H44, 30H60, 31,5H60) are compatible with caps made for standard BVP finishes according to EN 15543 - GLASS PACKAGING. FINISHES ...

See detail

GME30.15 - BVP and BVS minimum through bore

21/01/2022 - Latest update 07/06/2022

This data sheet specifies the values of the minimum through bore for BVP and BVS finishes. Users of bottles need to know the minimum through bore diameter to choose the filling tube; it was therefore useful to harmonise this dimension for each finish size.

See detail

GME30.21 - PET finish 30/25H (18.5)

01/12/2007

Specifications and dimensions of the 30 mm tall screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (18.5) is the height in millimetres from the top of finish ...

See detail

GME30.22 - PET finish 30/25-16.8-3/9

01/12/2007

Specifications and dimensions of the 30 mm low neck screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (16.8) is the height in millimetres from the top of ...

See detail

GME30.23 - PET finish 26.7/21.8-17-3/6.35

01/12/2008

Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 17.07 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper evident ...

See detail

GME30.24 - PET finish 26.7/21.7-16.8-3/3

01/12/2008

Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 16.80 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper evident ...

See detail

GME30.25 - PET finish 38/33-16,5-3/3

01/03/2009 - Latest update 01/07/2024

This document provides specifications and dimensions of the 38 mm screw finish with three (3) thread starts and a 16,50 mm height for still waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (1 bar max). This finish is ...

See detail

GME30.26 - PET finish 29/25-12,6-3/2,17

01/06/2009

Specifications and dimensions of the 29 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (12.6) is the height in millimetres from the top of finish to ...

See detail

GME30.27 - PET finish 28.3/22.5-59.5-1/3.6

01/09/2009

Specifications and dimensions of the screw PET finish BVS 30H60 for the closure of wines with CO2 content below 1.2 grams per litre. This finish is designed to take : An aluminium tamper-evident closure with an extended skirt which is reformed during application; A screw plastic ...

See detail

GME30.28 - PET finish 26/22-12-3/6.5

01/09/2011 - Latest update 01/04/2016

Specifications and dimensions of the 26 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for water with or without the introduction of nitrogen (internal Overpressure should not exceed 1 bar). The dimension (12.0) ...

See detail

GME30.29 - PET finish 37/32-17,5-2/3,63

13/05/2013 - Latest update 01/07/2024

Specifications and dimensions of the 38 mm screw finish with two (2) thread starts and a 17.55 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal overpressure should not exceed 1 bar). This ...

See detail

GME30.30 - PET finish 33/28-12.9-2/5

01/08/2011

This data sheet provides specifications and dimensions of the 33 mm screw finish with two (2) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar). This ...

See detail

GME30.31 - PET finish 32/26-15,8-2/2,7-(HF)

01/01/2016 - Latest update 15/03/2023

This document provides specifications and dimensions of the 32 mm amorphous screw finish with two (2) thread starts for still waters and non-carbonated beverages (the internal pressure should not exceed 1 bar). This finish can be used for hot filling (HF) with a maximum temperature up to ...

See detail

GME30.32 - PET finish 26/21-8.5 for edible oil

28/04/2014 - Latest update 23/12/2022

This document provides specifications and dimensions of the 26 mm finish designed for a snap-on plastic closure for non-carbonated products like edible oils, vinegar and sauces, cold filled (e.g. ambient temperature) with or without introduction of nitrogen (the internal pressure should not ...

See detail

GME30.33 - PET finish 29/21-10.5 for edible oil

28/04/2014 - Latest update 01/07/2021

This document provides specifications and dimensions of the 29 mm snap-on finish for non-carbonated products like alimentary oils, vinegar and sauces, cold filled (ambient temperature) with or without introduction of nitrogen (the internal pressure should not exceed 1 bar). This finish is ...

See detail

GME30.34 - BVS PCO PET finish 21,4/16,7-29-1/2,5

01/11/2014 - Latest update 17/01/2018

This data sheet provides specifications and dimensions of the BVS PCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar. This finish is designed to take a plastic tamper evident closure, which is applied by screwing.

See detail

GME30.35 - BVP MCO PET bague 21,4/16-29-1/2,5

20/09/2013 - Latest update 17/01/2018

This data sheet provides specifications and dimensions of the BVP MCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar. This finish is designed to take an aluminium tamper-evident closure, which is crimped during application.

See detail

GME30.36 - PET finish 32/27-14.9-2/2,7

14/11/2013 - Latest update 20/11/2023

This document provides specifications and dimensions of the 32 mm screw finish with two (2) thread starts for still waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar). This ...

See detail

GME30.37 - PET finish 26/22-12,9-1/2,17 version 4,2 % vol CO2

01/04/2016 - Latest update 01/10/2020

This data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages up to 8,4g CO2/l (4,2 vol % CO2) content and bottles of up to and including 2,0 l litres in capacity. Important note: This replaces previous editions foreseen ...

See detail

GME30.38 - PET finish 26/22-12-1/2,5

01/07/2015 - Latest update 25/11/2020

Specifications and dimensions of the 26 mm screw finish with one (1) thread start for carbonated beverages up to 7g/l CO2 content and for bottles up to 1,5 litres. The dimension (12,0) is the height in millimetres from the top of the finish to the bottom of the support ledge, offering line ...

See detail

GME30.39 - PET finish 25/22-9,5-3/1,73

01/07/2017 - Latest update 17/04/2020

Specifications and dimensions of the 25 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages in small package sizes with up to 1.5 l volume. This finish can be used for aseptic filling and filling with introduction of nitrogen (internal overpressure should ...

See detail

GME30.40 - PET finish 26/22-15,1-1/2,3

22/12/2022

This data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages, Up to 10,2g CO2/l (5,2 vol CO2) content for bottles of up to and including 2,0 litres in capacity, and up to 8,8g CO2/l (4,5 vol CO2) content and ...

See detail

GME30.41 - PET finish 26/22-13,4-1/2,3

10/07/2020 - Latest update 22/12/2022

This experimental data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages, Up to 10,2g CO2/l (5,2 vol CO2) content for bottles of up to and including 2,0 litres in capacity, and up to 8,8g CO2/l (4,5 vol CO2) ...

See detail

gme30.42 - PET finish 26/22-15,1-1/2,3 - HF - Exp.

26/01/2024

This data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages, Up to 10,2g CO2/l (5,2 vol CO2) content for bottles of up to and including 2,0 litres in capacity, and up to 8,8g CO2/l (4,5 vol CO2) content and ...

See detail

GME30.43 - PET finish 47/41-19,5-3/3,40

10/03/2021

This document provides specifications and dimensions of the 47 mm screw finish with three (3) thread starts for non-carbonated pressurised and non-pressurised beverages. This finish can be used for filling with introduction of nitrogen (internal overpressure should not exceed 1 bar). The ...

See detail

GME30.44 - Lightweight PET finish 29/25-12,6-3/2,17

28/07/2023 - Latest update 16/12/2024

This document provides specifications and dimensions of the 29 mm lightweight screw finish with three (3) thread starts for flat waters and other non-carbonated beverages. This finish can be used for filling with introduction of nitrogen (internal overpressure should not exceed 1 bar). The ...

See detail

GME30.70 - PET snap neck finish 26/21-8,5mm

10/12/2020

This document provides specifications and dimensions of the 26 mm finish designed for a snap-on plastic closure for non-pressurised and non-carbonated beverages cold-filled (e.g. ambient temperature) without the introduction of nitrogen. This finish is designed for snap-on plastic closure only, ...

See detail

GME305 - Pilferproof finishes for non-pressurised products supplementary series

02/11/1977 - Latest update 03/01/1983

Dimensions of a series of screw finishes for the closure of beverages and other non-carbonated products.

See detail

GME306 - 25 pilferproof finishes for Alpha syrup

01/03/1989

Dimensions of the 25 mm pilferproof glass neck finish for Alpha syrups.

See detail

GME307 - 28 pilferproof finishes for alpha syrups

01/03/1989

Dimensions of the 28 mm pilferproof glass neck finish for Alpha syrups.

See detail

GME32.00 - MCA finishes

01/06/2008 - Latest update 21/07/2022

This data sheet specifies the dimensions of the various 28-millimetre screw finish for glass containers designated MCA.

See detail

GME32.01 - 28mm screw finish for bottles with internal pressure

01/02/1995

Specifications and dimensions of the 28 millimetres screw finish for one-way or returnable glass containers with internal pressure designated MCA 3 finish. This document has been superseded by standard EN 17829 - GLASS PACKAGING - 28 MILLIMETRE-SCREW FINISHES (MCA RANGE) - DIMENSIONS.

See detail

GME32.02 - 28mm screw finish 7.5 RF universal for bottles with internal pressure

01/01/1983 - Latest update 01/11/1999

Specifications and dimensions of the 28 mm finish for glass containers for pressurised or vacuum liquids.

See detail

GME32.03 - PET PCO finish 27/22-21-1/3,18

01/06/2006 - Latest update 20/09/2021

Specifications and dimensions of the single start thread 27,43 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper-evident plastic closure only. During first opening, the tamper-evident band will separate from the closure shell and stay ...

See detail

GME32.04 - PET PCO finish 28/22-17-1/2.7

01/03/2009

Specifications and dimensions of the single start thread lightweight 28 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper-evident plastic closure only. During first opening, the tamper-evident band will separate from the closure shell ...

See detail

GME32.05 - MCA 1 finish

01/06/2009

Specifications and dimensions of the 28 millimetres screw finish for glass containers designated MCA 1 finish.

See detail

GME32.06 - MCA 7.5 R finish

01/06/2009 - Latest update 14/09/2023

This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 7,5 R finish for returnable glass.

See detail

GME320 - Pilferproof finish for pressured beverages

01/01/1983

See detail

GME33.01 - PET neck finish 27/22-13,5/1/4,24-1,5 turns for HPC applications

13/05/2019 - Latest update 22/12/2022

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 27,38 mm, and denominated as 27/22-13,5/1/4,24-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also ...

See detail

GME33.02 - PET neck finish 37/32-13,5/1/4,24-1,5 turns for HPC applications

23/04/2020 - Latest update 22/12/2022

This document aims to fully specify a PET Neck Finish standard for HPC market with a nominal crest of thread diameter of 37 mm and denominated as 37/32-13,5/1/4,24-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also ...

See detail

GME33.03 - PET neck finish 43/37-14,7-1/4,24-1,25 turns for HPC applications

23/04/2020 - Latest update 22/12/2022

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 43 mm and denominated as 43/37-14,7-1/4,24-1,25 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also ...

See detail

GME33.04 - PET neck finish 24/18-11,5-1/3,18-1,5 turns for HPC applications

29/10/2020 - Latest update 22/12/2022

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 23,67 mm and denominated as 24/18-11,5-1/3,18-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also ...

See detail

GME33.05 - PET neck finish 20/15-11,5-1/3,18-1,5 turns for HPC applications

16/12/2020 - Latest update 22/12/2022

This document aims to fully specify a PET Neck Finish standard for the HPC market with a nominal crest of thread diameter of 20mm and denominated as 20/15-11,5-1/3,18-1,5 turns (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also ...

See detail

GME33.50 - PET snap neck Finish 27/22-6,3 for HPC applications

10/06/2020 - Latest update 15/02/2021

This document aims to fully specify a PET Neck Finish standard for HPC market with a nominal crest of snap diameter of 27 mm, and denominated as 27/22-6,3 (for standard neck finish nomenclature, please refer to DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE). It also explains the dimensions ...

See detail

GME33.51 - PET snap neck finish 27/22-6,3 for HPC applications for high speed lines

15/09/2021 - Latest update 15/06/2022

This document is an adaptation of the GME33.50 - PET SNAP NECK FINISH 27/22-6,3 FOR HPC APPLICATIONS for high-speed lines. It aims to fully specify a PET Neck Finish standard for the HPC market with the nominal crest of snap diameter of 2 7 mm and denominated as 27 / 22 - 6,3. It also gives ...

See detail

GME40.02 - Flaconnage - Neck finish for plug pump

01/01/2005 - Latest update 13/09/2022

Specifications and dimensions of a series of finishes for pump systems with internal fixation on glass bottles.

See detail

GME40.03 - Flaconnage - Neck finish for snap-in pump

01/02/2006 - Latest update 25/05/2024

Specifications and dimensions of a finish for pump systems with internal fixation on glass bottles. See the example of pump references in table 1.

See detail

GME40.04 - Flaconnage - Neck finish for crimpless pump

01/01/2007 - Latest update 13/09/2022

Specifications and dimensions of a series of neck finishes for pump systems with external fixation, without crimping, on glass bottles. This geometry is dedicated to SP7 and SP8 from Silgan. Other crimpless pumps are adapted to standard EN 14854 - GLASS PACKAGING - DIMENSIONS OF NECK FINISHES ...

See detail

GME40.05 - Dimensions of the neck finish for glass aerosol containers

03/12/2014 - Latest update 29/04/2016

This data sheet specifies the dimensions of the neck finish of glass aerosol containers and pumps to ensure complete tightness of valves or pumps with finishes as defined in EN 14849 - AEROSOL CONTAINERS - GLASS CONTAINERS - DIMENSIONS OF AEROSOL VALVE FERRULES. It applies to moulded glass ...

See detail

GME40.06 - Stepped FEA finish

03/02/2022 - Latest update 06/12/2023

This range of FEA glass neck finishes with sizes 18 and 20 are designated for aerosol dispensers. This document was established from the INE BV96037 data sheet. The step of 0,2 mm can be used for protecting the upper part of the plastic coating and integrating it under the crimped ferrule.

See detail

GME40.07 - Flaconnage - Glass finish for screw pump - CV finish

08/12/2021

This data sheet is based on the INE BV95045 data sheet. It specifies the dimensions of a screw finish for glass flacons for the perfume or cosmetics industry. It applies to glass containers with a nominal diameter of the neck finish around 13, 15, 17, 18 or 20 mm. The designation is "CV ...

See detail

GME40.08 - Flaconnage - Neck finish '10,6' for snap-on pump type 'Replica ST'

30/01/2023 - Latest update 25/05/2024

This document specifies the dimensions of a 10,6-mm neck finish dedicated to a snap-on (crimpless) Replica ST pump from APTAR. ST stands for Seal-Tight.

See detail

GME40.10 - Flaconnage - Neck finish 11 mm for snap-on (Click-it) SP5-K pump

13/10/2023 - Latest update 21/11/2024

This document specifies the dimensions of an 11 mm neck finish dedicated to a snap-on (Click-it) 'SP5-K' pump from SILGAN.

See detail

GME40.20 - Flaconnage - Sustainable neck finishes - Screw neck without additional bead

17/03/2021 - Latest update 01/07/2024

This data sheet specifies dimensions of a screw neck finish without additional bead for glass bottles dedicated to perfume and cosmetics. It applies to glass containers with a nominal diameter of the neck finish around 13, 15 or 17 mm This neck finish is part of a range of neck finishes ...

See detail

GME40.25 - Flaconnage - Sustainable neck finishes - Interchangeable screw neck with additional bead

17/03/2021 - Latest update 01/07/2024

This data sheet specifies the dimensions of an interchangeable screw neck finish with additional bead for glass bottles dedicated to perfume and cosmetics. It applies to glass containers with a nominal diameter of the neck finish around 13, 15 or 17 mm This neck finish is part of a range of ...

See detail

GME40.30 - Flaconnage - Sustainable neck finishes - Interchangeable crimped finish with additional bead

17/03/2021 - Latest update 01/07/2024

This data sheet specifies the dimensions of an interchangeable crimped neck finish with additional bead for glass bottles dedicated to perfume and cosmetics. It applies to glass containers with a nominal diameter of the neck finish around 15 or 17 mm This neck finish is part of a range of ...

See detail

GME401 - Glass finish at 38mm standard ROPP (7 turns per inch)

01/09/1987

This data sheet provides specifications and dimensions for the 38 mm standard ROPP glass finish.

See detail

GME402 - Lug finish 20mm for antibiotic and freeze dry glass containers

01/06/1987

See detail

GME50.01 - Cork mouth finish for corks and capsules

01/04/1992

This data sheet specifies the dimensions of a cork mouth finish for corks and capsules for glass bottles, for wine that has a carbonation pressure not exceeding 2.0 g CO2/l, for use with natural corks.

See detail

GME50.02 - Glass bottle - Specifications of a neck finish with entry bore diameter 17,5mm

29/05/2024

This document sets out the dimensional characteristics of a finish with a narrow entry bore (diameter 17,5 mm) for bottles containing a wine that has a carbonation not exceeding 1,2 g CO2/l with internal sealing. Note: Carbonation over 1,2 g CO2/l requires a suitable container and stopper ...

See detail

GME51.00 - Glass bottle - Bartop stopper 27, 29, or 34 mm neck finish, stopper and overcap

02/10/2019

This datasheet sets out the dimensional characteristics of the finish of bottles intended for the packaging of alcohols, spirits, liquors and fortified wines and musts. It takes up and completes the dimensions contained in the French standard NFH 35 081 - BOTTLING INDUSTRY - GLASS BOTTLES - 27, ...

See detail

Finish data sheets (GME)

Cetie GME Series – Finish Specifications for Glass and PET Packaging