General data-sheets (DT)

You will find below the list of all available technical data-sheets.
The index DT (Technical Data-sheet) stands for Technical documents.
DT02.00 - STANDARD TOLERANCES FOR GLASS BOTTLES
01/12/1987 - Update 07/09/2018
Scope This document specifies capacity and dimension tolerances for glass bottles.
See detail
DT03.00 - GLASS BOTTLE DIMENSIONS
01/11/2002 - Update 11/07/2018
DT04.00 - DEFINITION OF CONDITION OF USE OF GLASS BOTTLES
01/06/1978 - Update 11/07/2018
DT06.00 - STANDARD EUROPEAN TOLERANCES FOR NORMAL WIDE MOUTH GLASS JARS
01/08/1998 - Update 11/07/2018
DT07.00 - DIMENSIONAL RELATIONSHIPS FOR NORMAL WIDE MOUTH GLASS JARS
01/02/1990 - Update 11/07/2018
Scope This data-sheet provides dimensional proportions of a typical wide-mouth jar made of glass.  It does not limit any other types of jars.
See detail
DT08.00 - SPECIAL STRENGTH PROPERTIES OF NEW GLASS BOTTLES FOR NON SPARKLING WINES
01/03/1980 - Update 11/07/2018
Scope This data sheet defines special strength properties for designs of new bottles for non-sparkling wines with less than 1 volume of carbonation (< 2 g/l). All new designs must be able to satisfy the requirements below.  Tests may also be carried out every shift during manufacture ...
See detail
DT09.00 - FACTORS TO CONVERT THE MASS OF WATER (IN G) TO TRUE VOLUME (IN ML)
01/09/1993 - Update 11/07/2018
DT10.00 - FILL LEVEL AT 20° FOR STD III 33CL, BS 33CL AND BS 25CL BOTTLES
01/10/1989 - Update 11/07/2018
DT11.00 - STANDARDS & PROCEDURES FOR THE CONTROL OF MANUFACTURE OF CARBONATED BEVERAGE BOTTLES FOR GREATER THAN 2g CO2/L CARBONATION
01/01/1989 - Update 12/01/2017
Scope The standards in this data sheet indicate when corrective action needs to be taken. The method for their use is described in section 2.
See detail
DT12.00 - GENERAL GUIDELINES FOR PREPARATION OF GLASS CONTAINERS QUALITY SPECIFICATIONS
01/09/1992 - Update 11/07/2018
Scope To assist preserve glass strength and improve glass handling throughout manufacture and filling.
See detail
DT13.00 - SURFACE TREATMENT
01/04/1992 - Update 11/07/2018
Scope The application of surface treatment preserves glass strength and improves glass handling throughout manufacture and filling. The outer surface of a glass container may be treated to reduce friction and to improve resistance to abrasion; Surface coatings are applied at two stages: ...
See detail
DT14.00 - GUIDELINES FOR THE USE OF GLASS CONTAINERS
01/01/1998 - Update 11/07/2018
Scope Glass containers are designed, manufactured and tested by the glass manufacturer to ensure that with proper use the containers will give a satisfactory and safe service throughout their intended life. Glass containers are produced in accordance with the relevant Cetie Data-sheets or ...
See detail
DT15.00 - FLACONNAGE - STANDARD TOLERANCES
20/11/2013 - Update 18/07/2018
Scope This data sheet identifies references to standard tolerances and test methods for flaconnage products made of moulded glass. It also provides a definition of ‘flaconnage’. These values are consistent with those given in standard ISO 12818.
See detail
DT15.01 - FLACONNAGE - BRIMFUL CAPACITY TOLERANCES
01/01/1996 - Update 18/07/2018
Scope This data sheet gives the recommended brimful capacity for flaconnage articles made of moulded glass.
See detail
DT15.02 - FLACONNAGE - HEIGHT TOLERANCES
01/01/1996 - Update 18/07/2018
Scope This data sheet gives the recommended height tolerances for flaconnage articles made of moulded glass.
See detail
DT15.03 - FLACONNAGE - DIAMETER AND WIDTH TOLERANCES
01/01/1996 - Update 18/07/2018
Scope This data sheet provides the recommended diameter and width tolerances for flaconnage articles made of moulded glass.
See detail
DT15.04 - FLACONNAGE - VERTICALITY TOLERANCES
01/01/1996 - Update 23/04/2018
Scope This data sheet gives the definition of the verticality and recommended tolerances of verticality for flaconnage articles made of moulded glass.
See detail
DT15.05 - FLACONNAGE - GLASS FINISH PLANARITY TOLERANCES - PRACTICAL VALUES IN USE IN THE INDUSTRY
01/12/2013 - Update 18/07/2018
Scope This data sheet gives the recommended planarity tolerances for the finishes of flaconnage containers made of moulded glass.
See detail
DT15.06 - FLACONNAGE - MOUTH-BASE PARALLELISM TOLERANCES: PRACTICAL VALUES IN USE IN THE INDUSTRY
01/12/2013 - Update 18/07/2018
Scope This data sheet gives the recommended tolerances of mouth-base parallelism for flaconnage containers made of moulded glass.
See detail
DT15.51 - FLACONNAGE - TESTING PROCEDURE: GLASS FINISH PLANARITY MEASUREMENT METHOD
16/12/2013 - Update 18/07/2018
Scope This data sheet gives the definition of the planarity of a finish for flaconnage articles made of moulded glass, and test procedures for its measurement. The planarity of the upper surface of top finish must comply with the requirements of the sealing system to be used on the glass ...
See detail
DT15.52 - FLACONNAGE - TESTING PROCEDURE: MEASUREMENT OF MOUTH-BASE PARALLELISM
16/12/2013 - Update 18/07/2018
Scope This data sheet gives test procedures to measure mouth-base parallelism for flaconnage articles made of moulded glass. The parallelism of the upper surface of the finish with respect to the base bearing surface should comply with the requirements of the closure system to be used on the ...
See detail
DT15.53 - FLACONNAGE - TESTING PROCEDURE: LEAKAGE TEST
16/05/2013 - Update 18/07/2018
Scope This data sheet describes a standard testing procedure to evaluate the liquid tightness of the glass-closure system for flaconnage subject to normal handling conditions, storage and transport. It may provide also an indication of gas tightness into or out of the container where this is ...
See detail
DT15.54 - FLACONNAGE - TESTING PROCEDURE: RESISTANCE TO VERTICAL LOAD
16/05/2013 - Update 18/07/2018
Scope This data sheet defines a test method to evaluate the resistance to vertical loading of flacons made of moulded glass. This test is intended to simulate vertical load to which containers may be subject both during capping operations and during storage and transport.
See detail
DT15.55 - FLACONNAGE - TESTING PROCEDURE: VERTICALITY
27/05/2015 - Update 18/07/2018
Scope This data sheet gives recommended test methods for determination of the verticality of glass flaconnage articles with complementary information to those described in EN 29008/ISO 9008.
See detail
DT16.00 - HYGIENE PRECAUTIONS - RECOMMENDATIONS FOR GLASS CONTAINERS MANUFACTURERS
01/01/2000 - Update 11/07/2018
Scope Where glass containers are being produced for the packaging of food, drink or pharmaceutical products the following hygiene precautions are recommended for consideration by glass manufacturers who do not already have equivalent and established Company rules on hygiene and where there is ...
See detail
DT19.00 - LABELLING SPOTTING BAR
01/01/1998 - Update 11/07/2018
DT20.00 - LOCATING DIMPLE FOR FLACONNAGE
01/01/2000 - Update 13/12/2016
DT20.10 - RAMP LOCATING SYSTEM FOR FLACONNAGE
01/01/2002 - Update 13/12/2016
DT21.00 - FLACONNAGE FINISHES
01/01/2008 - Update 14/12/2016
Scope This data sheet makes out the list of various glass finished used in flaconnage, following definition of CE.T.I.E. data sheet DT 15.00 Edition 1996.
See detail
DT22.00 - DEPRESSED THREAD
- Update 18/07/2018
Scope This data sheet specifies the profiles of thread for all the screw neck finishes for metallic, plastic and metallo-plastic closures. The depressed threads could be used on continuous thread finishes to reduce the thread depth at and adjacent to the mould parting line. Depressed threads ...
See detail
DT23.01 - GLASS CONTAINER NOMENCLATURE
01/05/2004 - Update 29/01/2019
Scope This data sheet gives in different languages the main parts of a glass bottle or jar. 
See detail
DT23.02 - NECK FINISH NOMENCLATURE
01/01/2004 - Update 15/12/2016
Scope This data sheet gives in different languages the different neck finishes parts of a glass bottle or jar.
See detail
DT23.03 - PET FINISHES GLOSSARY AND NOMENCLATURE
10/02/2016 - Update 14/05/2018
Scope This data sheet identifies the different parts of PET neck finishes and defines a standard nomenclature for the main dimensions according to that proposed by ISBT and consistent with the standard EN 16063. It also defines a standard format for naming Cetie PET finish specifications.
See detail
DT23.04 - PLASTIC CAP GLOSSARY AND NOMENCLATURE
18/08/2016 - Update 01/12/2017
Scope This data sheet identifies and proposes standard terms to describe different features of plastic screw caps and provides the nomenclature of the main characteristic dimensions. Main types of seal and tamper evident features are also described. The document covers flat top screw caps both ...
See detail
DT24.00 - SPECIFICATIONS FOR HAND-HELD CROWN BOTTLE OPENER
01/04/2002 - Update 11/07/2018
Scope This data sheet specification requirement for crown bottle openers designed for the standard 26 mm crown closures specified in Cetie data sheet EC 1-02 (1), to suit the glass bottle finishes specified in Cetie data sheets GME 13.01 (2) and GME 13.02 (3). It applies to hand-held openers of ...
See detail
DT25.00 - RECOMMENDATIONS FOR DESIGN OF CORK REMOVAL DEVICES
01/03/2002 - Update 11/07/2018
Scope This data sheet gives recommendations for the design of devices for removing corks from wine bottles. Corks can be made of cork or plastic/synthetic material.
See detail
DT26.00 - GLOSSARY OF GLASS CONTAINER VISUAL CRITICAL DEFECTS
01/10/2007 - Update 12/01/2017
Scope This document is a non-exhaustive list of examples of visual critical defects. It constitutes a general data sheet for all containers of all types, except those for cosmetics and perfumes. It does not preclude specific requirements agreed between bottlers and suppliers at a customer level.
See detail
DT26.01 - GLOSSARY OF GLASS CONTAINERS VISUAL DEFECTS
01/10/2007 - Update 14/02/2019
Scope This glossary is proposed as an aid to identify visual defects. It constitutes a general data sheet for glass containers of all types, except those for cosmetics and perfumes. Separately, if values of severity are required for particular features, such values should be agreed between the ...
See detail
DT26.10 - GLOSSARY OF GLASS CONTAINER VISUAL CRITICAL DEFECTS FOR COSMETICS & PERFUMES
01/01/2009 - Update 12/01/2017
Scope This document is a non-exhaustive list of examples of visual critical defects. It constitutes a general data sheet for containers for cosmetics and perfumes. It does not preclude specific requirements agreed between customers and suppliers.
See detail
DT27.00 - CROSS-RELATIONSHIPS BETWEEN CETIE DOCUMENTS AND INTERNATIONAL STANDARDS
03/06/2013 - Update 11/07/2018
Scope This data sheet gives identified cross relationships between Cetie documents and National/European/International standards or other recognized reference documentation. The list may not be exhaustive and is subject to modifications. It is thus recommended not to conserve printed versions ...
See detail
DT28.00 - LASER CODES ON GLASS CONTAINERS DURING FILLING
01/07/2008 - Update 11/07/2018
Scope This data sheet gives the areas to avoid for the marking of laser codes on glass bottles and jars during filling. Marking in these areas may have an adverse effect on the strength of the container dependant on the applied stress
See detail
DT29.00 - GENERAL APPLICATION TORQUES FOR FLACONNAGE
01/02/2007 - Update 14/12/2016
Scope This data sheet specifies general application torque values for plastic closures used with glass containers for cosmetics, pharmaceutical and toiletry products. Note Specific values should be sought from closure and liner manufacturers for particular uses. Child Resistant Closures ...
See detail
DT30.00 - COLOUR MEASUREMENT OF GLASS PACKAGING
01/07/2008 - Update 15/12/2016
Scope This data sheet aims to: - advise basic knowledge of colorimetry - specify the important points for a colour measurement - propose a reference for colour measurement of glass packaging.
See detail
DT31.00 - MAIN TYPES OF SEALING
01/06/2004 - Update 11/07/2018
Scope This document is a non-exhaustive list of main types of sealing for bottles and jars, used for the packing of beverages, food products and flaconnage products (cosmetic and pharmacy). It also lists corresponding reference-documents concerning the particular finishes. For finishes used ...
See detail
DT32.00 - VOLUME CALCULATION
19/01/2013 - Update 20/09/2018
Scope This Data Sheet gives a common reference frame for the calculation of the brimful volume of a glass container as it is presented in the specification drawings. It applies to all cylindrical jars and bottles made of glass, manufactured on I.S. machines. It enables a standardized volume ...
See detail
DT33.00 - IMPACT TESTING OF GLASS CONTAINERS
01/04/2015 - Update 29/01/2019
Scope Test to predict the glass container resistance to impact breakage in service, by multiple point impacts on empty samples, commonly carried out with a pendulum impact tester. Three usual forms of this test are considered, according to the objective: Determination of the impact ...
See detail
DT34.00 - TEST-METHOD OF COMPRESSIBILITY AND ELASTIC RECOVERY
03/12/2013 - Update 18/07/2017
Scope Elastic recovery and compressibility comparative measurements of the liner material.
See detail
DT35.00 - FLACONNAGE: PLANARITY TEST OF LABELLING AREA
06/06/2017 - Update 15/10/2018
Scope This document describes standard test methods used to detect surface defects on a glass flacon on which a label needs to be applied. These defects can cause visual imperfections of the flacon (air bubbles or wrinkles under the label, for example).
See detail
DT38.00 - ROLL-ON PILFER PROOF CLOSURE: REMOVAL TORQUE - TEST METHOD
02/05/2018 - Update 30/05/2018
Scope This document provides a test method to measure the removal torque for ROPP closures applied to glass finishes.
See detail