Finishes data-sheets (GME)

The section lists all available data sheets for finishes of bottles and jars made of glass or PET.

The index GME refers to the Finish data-sheets category, then the first two digits refer to the following "families":

GME 13 series: Crown finishes
GME 14 series: Threaded crown finishes
GME 20 series: Vacuum lug finishes for bottles and wide mouth jars
GME 30 series: Pilferproof threaded finishes
GME 32 series: Threaded finishes for pressurised beverages
GME 40 series: Crimp-on finishes
GME 50 series: Cork mouth finishes
GME 306 - 25 PILFERPROOF FINISHES FOR ALPHA SYRUP
01/03/1986 - Update 12/01/2017
GME 307 - 28 PILFERPROOF FINISHES FOR ALPHA SYRUP
01/03/1989 - Update 12/01/2017
GME 320 - PILFERPROOF FOR PRESSURED BEVERAGES
01/01/1983 - Update 12/01/2017
GME 401 - GLASS FINISH AT 38 MM STD ROPP
01/09/1987 - Update 12/01/2017
GME 402 - LUG FINISH 20 MM FOR ANTIBIOTIC AND FREEZE DRY GLASS CONTAINERS
01/06/1987 - Update 12/01/2017
GME13.01 - 26 H 180 CROWN FINISH
- Update 08/12/2016
Scope Specifications and dimensions of the 26 mm tall crown finish for glass bottles containing beverages.
See detail
GME13.02 - 26 H 126 CROWN FINISH
01/06/2007 - Update 08/12/2016
Scope Specifications and dimensions of the 26 mm shallow crown finish for glass bottles containing beverages.
See detail
GME13.04 - 29 MM SPARKLING WINE FINISH
01/10/1998 - Update 10/05/2018
Scope This data sheet gives dimensions and specifications of the 29 mm glass finish for bottles intended for sparkling wine produced by a closed tank method. This finish is designed to take a cork closure in natural cork or synthetic material.
See detail
GME13.05 - 29 MM SPUMANTE CROWN FINISH
01/10/1998 - Update 10/05/2018
Scope This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for Spumante type sparkling wines. This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.
See detail
GME13.06 - 29 MM CIDER CROWN FINISH
01/10/1998 - Update 10/05/2018
Scope This data sheet gives dimensions and specifications of the 29 mm crown finish for glass bottles intended for cider. This finish is designed to take a crown closure or a cork closure in natural cork or synthetic material.
See detail
GME13.07 - COMPARISON OF GLASS FINISHES FOR SPARKLING WINES AND OTHER CARBONATED BEVERAGES
23/06/2017 - Update 10/05/2018
Scope This data sheet gives an overview of the main available glass finishes available for sparkling wines and other carbonated beverages with a stopper made of cork or synthetic material, generally maintained in place with a wire cage, with or without the possibility of alternatively receiving ...
See detail
GME13.08 - TRADITIONAL METHOD SPARKLING WINE FINISHES (26, 29, 36 MM)
12/01/2018 - Update 15/01/2018
Scope This data sheet gives dimensions and specifications of the glass finishes for bottles intended for sparkling wine produced by the “traditional method”, with a diameter of 26, 29 or 36 mm.
See detail
GME13.11 - 26 H 180 CROWN FINISH - DIMENSIONS - MODIFIED ''P'' POINT
12/01/2018 - Update 01/03/2018
Scope This data sheet provides specifications and dimensions of the 26 H 180  mm tall crown finish for glass bottles with a modified "P" point.
See detail
GME13.12 - 26 H 126 CROWN FINISH - DIMENSIONS - MODIFIED ''P'' POINT
12/01/2018 - Update 01/03/2018
Scope This data sheet provides specifications and dimensions of the 26 H 126  mm shallow crown finish for glass bottles with a modified "P" point.
See detail
GME14.01 - 26 H 180 TWIST CROWN FINISH
01/07/2003 - Update 09/01/2017
Scope Specifications and dimensions of the 26 mm tall twist crown finish for glass bottles containing beverages.
See detail
GME14.02 - 26 H 126 TWIST CROWN FINISH
01/07/2013 - Update 08/12/2016
Scope Specifications and dimensions of the 26 mm shallow twist crown finish for glass bottles containing beverages.
See detail
GME14.11 - 26 H 180 TWIST CROWN FINISH - REDUCED BORE
- Update 18/01/2018
Scope This data sheet provides specifications and dimensions of the 26 H 180  mm tall twist crown finish for glass bottles with a reduced bore.
See detail
GME14.12 - 26 H 126 TWIST CROWN FINISH - REDUCED BORE
12/01/2018 - Update 18/01/2018
Scope This data sheet provides specifications and dimensions of the 26 H 126  mm shallow twist crown finish for glass bottles with a reduced bore.
See detail
GME20.00 - VACUUM LUG FINISH Ø 33 Medium
01/01/1995 - Update 06/01/2017
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 33 mm medium for wide-mouth glass containers.  
See detail
GME20.00.10 - VACUUM LUG FINISH Ø 27 REGULAR (Experimental)
01/07/2003 - Update 28/12/2016
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 27 mm medium for wide-mouth glass containers.
See detail
GME20.00.20 - VACUUM LUG FINISH Ø 30 AND Ø 33 MEDIUM (EXPERIMENTALE)
01/07/2003 - Update 12/01/2017
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 30  et 33 mm medium for wide-mouth glass containers.
See detail
GME20.01 - VACUUM LUG FINISH DIAM.27 AND 38 REGULAR
01/01/1995 - Update 12/01/2017
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm regular for wide-mouth glass containers.
See detail
GME20.02 - VACUUM LUG FINISH DIAM 38 MEDIUM
01/01/1995 - Update 28/12/2016
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.
See detail
GME20.02.10 - VACUUM LUG FINISH DIAM. 38 MEDIUM (Experimental)
01/07/2003 - Update 28/12/2016
Scope This data-sheet specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers.
See detail
GME20.03 - VACUUM LUG FINISH DIAM. 43 AND 48 REGULAR (Experimental)
01/01/1995 - Update 28/12/2016
Scope This data-sheet specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers.
See detail
GME20.04 - VACUUM LUG FINISH DIAM. 53 AND 58 REGULAR
01/01/1995 - Update 14/09/2018
Scope This document specifies the dimensions of vacuum lug finishes with nominal sizes of 53 mm and 58 mm regular for wide-mouth glass containers.
See detail
GME20.05 - VACUUM LUG FINISH DIAM.58 DEEP
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of vacuum lug finish with nominal size of 58 mm deep for wide-mouth glass containers.
See detail
GME20.06 - VACUUM LUG FINISH Ø 63, Ø 66 Ø 70 REGULAR (Experimental)
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm regular for wide-mouth glass containers.
See detail
GME20.07 - VACUUM LUG FINISH Ø 63, Ø 66 Ø 70 DEEP (Experimental)
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.
See detail
GME20.08 - VACUUM LUG FINISH DIAM.77 REGULAR
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for wide-mouth glass containers.
See detail
GME20.09 - VACUUM LUG FINISH DIAM.82 REGULAR
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of a vacuum lug finish with a nominal size of 82 mm regular for wide-mouth glass containers.
See detail
GME20.10 - VACUUM LUG FINISH DIAM.89 REGULAR
01/01/1995 - Update 28/12/2016
Scope This document specifies the dimensions of a vacuum lug finish with a nominal size of 89 mm regular for widemouth glass containers.
See detail
GME20.11 - VACUUM LUG FINISH DIAM.100 REGULAR
01/01/1995 - Update 23/06/2017
Scope This document specifies the dimensions of a vacuum lug finish with a nominal size of 100 mm regular for wide-mouth glass containers.
See detail
GME20.12 - VACUUM LUG FINISH DIAM.110 REGULAR
01/01/1995 - Update 12/01/2017
Scope This document specifies the dimensions of a vacuum lug finish with a nominal size of 110 mm regular for wide-mouth glass containers.
See detail
GME25.01 - PRESS ON VACUUM SEAL FINISH Ø 51 Ø 63 Ø 70
28/08/2013 - Update 20/12/2018
GME28.01 - PRESS ON VACUUM SEAL FINISH Ø 51 TAMPER EVIDENT
29/08/2013 - Update 20/12/2018
GME30.06 - BVP SCREW FINISHES FOR NON CARBONATED PRODUCTS
01/10/2001 - Update 23/06/2017
Scope Specifications and dimensions of a series of screw finishes for the closure of beverages and other non-carbonated products. Finishes designed to take a tamper-evident closure which needs to be snapped before it can be opened, commonly known as a rolled on Pilferproof closure.  The ...
See detail
GME30.07 - 30 EXTRA DEEP BVP FINISH FOR NON-REFILLABLE INSERT
01/04/2005 - Update 11/05/2018
Scope Specifications and dimensions of the 30 extra deep finish concerning bore diameter and profile. Finish designed to take a non refillable insert for ≤ or 150 cl bottles.
See detail
GME30.08 - 31.5 DEEP BVP FINISH FOR NON-REFILLABLE INSERT
01/10/2001 - Update 11/05/2018
Scope Spécifications and dimensions of the 31.5 deep BVP finish concerning bore diameter and profile.
See detail
GME30.09 - 31.5 STANDARD BVP FINISH FOR POURER
01/10/2001 - Update 11/05/2018
Scope Specifications and dimensions of the 31.5 standard BVP finish concerning bore diameter and profile.
See detail
GME30.10 - BORE SPECIFICATIONS FOR INSERTS FOR 30, 31.5 AND 35 SIZE BVP FINISHES
01/06/2010 - Update 11/05/2018
Scope This data sheet gives the specifications of bore dimensions and profile for BVP finishes according to EN 15543 for 30, 31,5 and 35, standard, deep and extra deep versions, in order to accept pourers or non-refillable inserts, for bottles with a capacity ≤ 150 cl. As with all BVP type ...
See detail
GME30.11 - FINISH ALSECO-ALCOA 28
01/01/2000 - Update 13/12/2016
GME30.12 - FINISH GL
01/01/2002 - Update 13/12/2016
GME30.13 - DEEP BVS FINISHES FOR STILL WINES
01/12/2008 - Update 13/06/2017
Scope Specifications and dimensions of a series of deep screw glass finishes for the closure of wines with a CO2 content below 1.2 g/l. Note Carbonation ≥ 1,2g/l in CO2 requires an appropriate bottle and an adapted capping method agreed between the glass maker, the cap supplier and ...
See detail
GME30.21 - PET FINISH 30/25 H (18.5)
01/12/2007 - Update 01/12/2016
Scope Specifications and dimensions of the 30 mm tall screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (18.5) is the height in millimetres from the top of ...
See detail
GME30.22 - PET FINISH 30/25-16.8-3/9
01/12/2007 - Update 01/12/2016
Scope Specifications and dimensions of the 30 mm low neck screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (16.8) is the height in millimetres from the top ...
See detail
GME30.23 - PET FINISH 26.7/21.8-17-3/6.35
01/12/2008 - Update 01/12/2016
Scope Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 17.07 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper ...
See detail
GME30.24 - PET FINISH 26.7/21.7-16.8-3/9
01/12/2008 - Update 01/12/2016
Scope Specifications and dimensions of the 26.7 mm screw finish with three (3) thread starts and a 16.80 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper ...
See detail
GME30.25 - PET FINISH 38/33.4-16.5-3/9
01/03/2009 - Update 08/08/2018
Scope This document provides specifications and dimensions of the 38 mm screw finish with three (3) thread starts and a 16,50 mm height for still waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (1 bar max). It is ...
See detail
GME30.26 - PET FINISH 29/25-12.6-3/6.5 (Experimental)
01/06/2009 - Update 12/01/2017
Scope Specifications and dimensions of the 29 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (12.6) is the height in millimetres from the top of ...
See detail
GME30.27 - PET FINISH 28.3/22.5-59.5-1/3.6
01/09/2009 - Update 30/11/2016
Scope Specifications and dimensions of the screw PET finish BVS 30H60 for the closure of wines with CO2 content below 1.2 grams per litre.  This finish is designed to take : An aluminium tamper-evident closure with extended skirt which is reformed during application A screw plastic ...
See detail
GME30.28 - PET FINISH 26/22-12-3/6.5
01/09/2011 - Update 30/11/2016
Scope Specifications and dimensions of the 26 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages.  This finish can be used for water with or without introduction of nitrogen (internal Overpressure should not exceed 1 bar).  The dimension ...
See detail
GME30.29 - PET FINISH 37/32-17.5-2/7.26
13/05/2013 - Update 27/03/2018
Scope Specifications and dimensions of the 38 mm screw finish with two (2) thread starts and a 17.55 mm height for flat waters and non carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal overpressure should not exceed 1 bar). ...
See detail
GME30.30 - PET FINISH 33/28-12.9-2/5
01/08/2011 - Update 01/12/2016
Scope This data-sheet provides specifications and dimensions of the 33 mm screw finish with two (2) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar). ...
See detail
GME30.31 - PET FINISH 32/26-15.2-2/5.4
01/01/2016 - Update 29/11/2017
Scope This document provides specifications and dimensions of the 32 mm amorphous screw finish with two (2) thread starts for still waters and non-carbonated beverages (the internal pressure should not exceed 1 bar). This finish can be used for hot filling with a maximum temperature up to ...
See detail
GME30.32 - PET FINISH 26/21-8.5-0
28/04/2014 - Update 06/04/2017
Scope This document provides specifications and dimensions of the 26 mm finish designed for a snap-on plastic closure for non-carbonated products like edible oils, vinegar and sauces, cold filled (e.g. ambient temperature) with or without introduction of nitrogen (the internal pressure should ...
See detail
GME30.33 - PET FINISH 29/21-10.5
28/04/2014 - Update 06/04/2017
Scope This document provides specifications and dimensions of the 29mm snap-on finish for non-carbonated products like alimentary oils, vinegar and sauces, cold filled (ambient temperature) with or without introduction of nitrogen (the internal pressure should not exceed 1 bar). This finish is ...
See detail
GME30.34 - BVS PCO PET FINISH 21,4/16,7-29-1/2,5
01/11/2014 - Update 22/01/2018
Scope This data sheet provides specifications and dimensions of the BVS PCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar. This finish is designed to take a plastic tamper-evident closure, which is applied by screwing.
See detail
GME30.35 - BVP MCO PET FINISH 21,4/16-29-1/2,5
20/09/2013 - Update 17/01/2018
Scope This data sheet provides specifications and dimensions of the BVP MCO 22H30 PET screw finish for wines with a maximum internal pressure of 1 bar. This finish is designed to take an aluminium tamper-evident closure, which is crimped during application.
See detail
GME30.36 - PET FINISH 32/27-14.9-2/5.4
14/11/2013 - Update 06/03/2018
Scope Specifications and dimensions of the 32 mm screw finish with two (2) thread starts for still waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (the internal pressure should not exceed 1 bar). This finish is ...
See detail
GME30.37 - PET FINISH 26/22-13-1/2.17 (Experimental)
20/02/2017 - Update 06/03/2018
Scope This experimental data sheet provides specifications and requirements of the 26/22 mm screw finish with one (1) thread start for carbonated beverages up to 7g/l CO2 content and up to 2,0 l bottle size. This finish is intended for non-refillable bottles, has vent slots and is designed to ...
See detail
GME30.38 - PET FINISH 26/22-12-1/2.5
01/07/2015 - Update 06/04/2017
Scope Specifications and dimensions of the 26 mm screw finish with one (1) thread start for carbonated beverages up to 7g/L CO2 content and for bottles up to 1.5 litres. The dimension (12.0) is the height in millimetres from the top of finish to the bottom of the support ledge, offering line ...
See detail
GME30.39 - PET FINISH 25/22-9-3 (Experimental)
11/01/2016 - Update 07/02/2018
Scope Specifications and dimensions of the 25 mm screw finish with three (3) thread starts for flat waters and non carbonated beverages in small package sizes with up to 1.5l volume. This finish can be used for aseptic filling and filling with introduction of nitrogen (internal overpressure ...
See detail
GME32.00 - MCA FINISHES
01/10/2008 - Update 28/12/2016
Scope This data sheet gives a comparison and a brief history of various 28 millimetres screw finishes designated “MCA finishes”. 
See detail
GME32.01 - 28 mm SCREW FINISH FOR BOTTLES WITH INTERNAL PRESSURE (Experimental)
01/01/1993 - Update 14/09/2018
Scope Specifications and dimensions of the 28 millimetres screw finish for one way or returnable glass containers with internal pressure designated MCA 3 finish. This document has been superseded by standard CEN 16288.  
See detail
GME32.02 - 28 mm SCREW FINISH 7.5 RF UNIVERSAL FOR BOTTLES WITH INTERNAL PRESSURE
01/01/1983 - Update 14/09/2018
Scope Specifications and dimensions of the 28 mm finish for glass containers for pressurized or vacuum liquids. This document has been superseded by standard CEN 16289.  
See detail
GME32.03 - PET PCO FINISH 28/22-21-1/3.18
01/06/2006 - Update 01/12/2016
Scope Specifications and dimensions of the single start thread 28 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and ...
See detail
GME32.04 - PET PCO FINISH 28/22-17-1/2.7
01/03/2009 - Update 01/03/2018
Scope Specifications and dimensions of the single start thread lightweight 28 mm PET PCO screw finish for the beverage industry. This finish has vent slots and is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure ...
See detail
GME32.05 - MCA 1 FINISH
01/06/2009 - Update 28/12/2016
Scope Specifications and dimensions of the 28 millimetres screw finish for glass containers designated MCA 1 finish.
See detail
GME32.06 - MCA 7.5 R FINISH
01/06/2009 - Update 28/12/2016
Scope This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 7,5 R finish for returnable glass.
See detail
GME40.02 - FINISH FOR PLUG PUMP
01/01/2005 - Update 13/12/2016
Scope Specifications and dimensions of a series of finishes for pump systems with internal fixation on glass bottles. 
See detail
GME40.03 - FINISH FOR SNAP'IN PUMP
01/01/2007 - Update 13/12/2016
Scope Specifications and dimensions of a series of finishes for pump systems with internal fixation on glass bottles. 
See detail
GME40.04 - FINISH FOR CRIMPLESS PUMP
01/01/2007 - Update 14/12/2016
Scope Specifications and dimensions of a series of finishes for pump systems with external fixation, without crimping, on glass bottles.
See detail
GME40.05 - DIMENSIONS OF THE NECK FINISH FOR GLASS AEROSOL CONTAINERS
03/12/2013 - Update 10/05/2017
Scope This data-sheet specifies dimensions of glass containers neck finish for aerosols containers, in order to guarantee tight sealing of valves or pumps with ferrules defined by EN 14849. It applies to aerosols containers and pumps which have a neck diameter of 13mm, 15mm, 17mm, 18mm et 20mm ...
See detail
GME50.01 - CORK MOUTH FINISH FOR CORKS AND CAPSULES
01/01/2000 - Update 28/12/2016
Scope This data-sheet specifies the dimensions of a cork mouth finish for corks and capsules for glass bottles, for wine that has a carbonation pressure not exceeding 2.0 g CO2/l, for use with natural corks.
See detail